Control flow module¶

Total OWS request count¶

The global number of OWS requests executing in parallel can be specified with:

ows.global=<count>

Every request in excess will be queued and executed when other requests complete leaving some free execution slot.

Per request control¶

A per request type control can be demanded using the following syntax:

ows.<service>[.<request>[.<outputFormat>]]=<count>

Where:

• <service> is the OWS service in question (at the time of writing can be wms, wfs, wcs)

• <request>, optional, is the request type. For example, for the wms service it can be GetMap, GetFeatureInfo, DescribeLayer, GetLegendGraphics, GetCapabilities

• <outputFormat>, optional, is the output format of the request. For example, for the wms GetMap request it could be image/png, image/gif and so on

A few examples:

# don't allow more than 16 WCS requests in parallel
ows.wcs=16
# don't allow more than 8 GetMap requests in parallel
ows.wms.getmap=8
# don't allow more than 2 WFS GetFeature requests with Excel output format
ows.wfs.getfeature.application/msexcel=2

Request priority support¶

Requests controlled by “ows.*” controllers above can be also executed in priority order, in case there are too many the request will block and wait, and will we awoken in priority order (highest to lowest).

Currently the only way to specific a priority for a request is to add it to a request HTTP header:

ows.priority.http=<headerName>,<defaultPriority>

The header “headerName” will contain a number defining the priority for the request, the default priority is used as a fallback if/when the header is not found.

Using a header implies some other system is involved in the priority management. This is particularly good when using a load balancer, as the requests priorities need to be evenly split across cluster elements, control-flow only has visibility of a single instance. As an example, the priority will be de facto ignored at the cluster level if there are two nodes, and for whatever chance or design, the high priority requests end up converging on the same cluster node.

Per user concurrency control¶

There are two mechanisms to identify user requests. The first one is cookie based, so it will work fine for browsers but not as much for other kinds of clients. The second one is ip based, which works for any type of client but that can limit all the users sitting behind the same router

This avoids a single user (as identified by a cookie) to make too many requests in parallel:

user=<count>

Where <count> is the maximum number of requests a single user can execute in parallel.

The following avoids a single ip address from making too many requests in parallel:

ip=<count>

Where <count> is the maximum number of requests a single ip address can execute in parallel.

It is also possible to make this a bit more specific and throttle a single ip address instead by using the following:

ip.<ip_addr>=<count>

Where <count> is the maximum number of requests the ip specified in <ip_addr> will execute in parallel.

To reject requests from a list of ip addresses:

ip.blacklist=<ip_addr1>,<ip_addr2>,...

Per user rate control¶

The rate control rules allow to setup the maximum number of requests per unit of time, based either on a cookie or IP address. These rules look as follows (see “Per user concurrency control” for the meaning of “user” and “ip”):

user.ows[.<service>[.<request>[.<outputFormat>]]]=<requests>/<unit>[;<delay>s]
ip.ows[.<service>[.<request>[.<outputFormat>]]]=<requests>/<unit>[;<delay>s]

Where:

• <service> is the OWS service in question (at the time of writing can be wms, wfs, wcs)

• <request>, optional, is the request type. For example, for the wms service it can be GetMap, GetFeatureInfo, DescribeLayer, GetLegendGraphics, GetCapabilities

• <outputFormat>, optional, is the output format of the request. For example, for the wms GetMap request it could be image/png, image/gif and so on

• <requests> is the number of requests in the unit of time

• <unit> is the unit of time, can be “s”, “m”, “h”, “d” (second, minute, hour and day respectively).

• <delay> is an optional the delay applied to the requests that exceed the maximum number of requests in the current time slot. If not specified, once the limit is exceeded a immediate failure response with HTTP code 429 (“Too many requests”) will be sent back to the caller.

The following rule will allow 1000 WPS Execute requests a day, and delay each one in excess by 30 seconds:

user.ows.wps.execute=1000/d;30s

The following rule will instead allow up to 30 GetMap requests a second, but will immediately fail any request exceeding the cap:

user.ows.wms.getmap=30/s

In both cases headers informing the user of the request rate control will be added to the HTTP response. For example:

X-Rate-Limit-Context: Any OGC request
X-Rate-Limit-Limit: 10
X-Rate-Limit-Remaining: 9
X-Rate-Limit-Reset: 1103919616
X-Rate-Limit-Action: Delay excess requests 1000ms

In case several rate control rules apply to a single request, a batch of headers will be added to the response for each of them, it is thus advised to avoid adding too many of these rules in parallel

Where:

• X-Rate-Limit-Context is the type of request being subject to control

• X-Rate-Limit-Limit is the total amount of requests allowed in the control interval

• X-Rate-Limit-Remaining is the number of remaining requests allowed before the rate control kicks in

• X-Rate-Limit-Reset is the Unix epoch at which the new control interval will begin

• X-Rate-Limit-Action specifies what action is taken on requests exceeding the rate control

Timeout¶

A request timeout is specified with the following syntax:

timeout=<seconds>

where <seconds> is the number of seconds a request can stay queued waiting for execution. If the request does not enter execution before the timeout expires it will be rejected.